should spacers be used behind ledger board and house

  • How to Attach a Deck Ledger to the House - Fine Homebuilding

    10 Dec 2010 ... He cites Rob Thallon's Graphic Guide to Frame Construction, which describes the use of 3/4-in. spacers filled ... Any water trapped behind the ledger can induce rot, if not in the ledger itself than in sheathing and framing of the house. ... Then he adds this curious note: "Your ledger board should not be carrying any of the deck weight, that is the job of girders/beams. ... "If one used beams for both load points (at house and at edge of deck) then no ledger should be used.

  • Attach the Ledger | How to Build a Simple Deck | This Old House

    Align the top of each spacer with the chalk line and fasten with a 6d nail. Align the ledger with the tops of the spacers and nail it to the wall at each spacer with a 16d nail. (Joints between ledger boards should fall on a spacer.) Drill a 3鈪?inch ...

  • Deck Ledger Spacers - Decks.com

    Learn how to install deck ledger board spacers to allow air to flow behind your ledger board to prevent rot. ... Decks.com - Home ... Multiple stainless steel washers can be used or a variety of engineered products designed specifically for this ...

  • Attaching the Ledger Board | Deck Building Project - Deck Designs

    Deck Building Project - See how a waterproof ledger board for this deck was installed on an existing home. ... So you will learn how the siding was removed and two layers of metal waterproof flashing were installed around the board. ... But it's also less labor intensive and uses fewer materials than digging holes and setting another set of posts and beams to create a stand ... Flashing in behind ledger.

  • Keeping Water Out of Decks - Professional Deck Builder Magazine

    1 May 2012 ... Protecting a house against water intrusion starts with creating a barrier, such as siding, that moves water away from ... Otherwise, water will get behind the ledger board and cause damage to the siding and the sheathing. ... However, it doesn't take paint well and should be used cautiously near areas that will be painted. ... One way to stop water from collecting in the groove in between them is to space the joists apart with pressure-treated plywood spacers (Figure 3).

  • Flashing A Deck Ledger Board Properly - Home Construction ...

    I will need to cut out the siding to add the ledger board, so what is the best way to extend the flashing up behind the siding ..... I used galvanized steel, but as extra protection, I cut a strip of ice & water shield and laid it on top of the ledger board before the ..... (8脳8 post on the other side) I have a concrete block house and plan to use a Ledger with spacers in between the house (concrete block) and Ledger.

  • Deck Ledger Board Installation - InspectAPedia.com

    The ledger is a board that is bolted to the house to support one end of the deck joists. It is a bit of a hybrid鈥攑art ... Alternatively, wood spacers can be cut out of pressure-treated plywood and placed behind the ledger. As added ... Connecting a Deck Ledger when the Building Used Nonstandard Building Joists. If the floors in ...

  • Deck Ledger Attachment Methods | Structure Tech Home Inspections

    8 May 2012 ... The piece of wood that connects a deck to a building is called the ledger, or ledger board. I'll be using this term ... One problem that I occasionally find with lag screws is that they're not attached to anything substantial behind the ledger. When a home is ... Through-bolts can be used to attach a ledger to the house when the interior of the rim joist is accessible. This is typically done using ...

  • Step 3. Attaching the Ledger Board to the House - Perfect Pergolas ...

    Fig 10 above shows a picture of the ledger board and the suggested fixing holes and spacings that you should pre-drill. ... By using the spacers provided, it creates a gap between the ledger board and the wall itself which allows air to flow and ...

  • How do I attach a ledger board if I have no interior access? - Home ...

    18 Oct 2010 ... I have the deck plans all laid out, and am in need of a 2x10 ledger board under the door to attach the deck to. ... then seek a bit of professional advise or go to a self supporting deck. simple cross bracing will make a very stable deck not attached to house. .... What type of lag bolts should I use for a deck?

Leave a Reply

Simply complete the form below, click submit, you will get the price list and a Seventrust representative will contact you within one business day.
( * Denotes a required field).